安规仪器网|美华安规仪器
  • 设为首页|收藏本站|繁体中文|WAP
  • 安规论坛 安规学院 证书查询 安规工具 安规测试 仪器使用 资讯中心 标准下载 标准汇总 学术论文

    仪器商城     更多仪器     搜索中心

  • 网站首页
  • 商城
  • 耗材
  • 试指
  • 量规
  • 灯规
  • 通用
  • 电池
  • 插头
  • 电线
  • 灯具
  • 家电
  • 燃烧
  • 橡塑
  • IP防水
  • 环境
  • 音视
  • 信息
  • 电学
  • 量具
  • 力学
  • 方案
  • 更多
  • 客服

量规

UL美国实验室量规
IEC器具耦合器|连接器

IEC60320|GB17465|UL60320

IEC60309|GBT11919|11918

日本JIS|台湾CNS标准

日本JIS C8303|C 8282-1治具

台湾CNS690|CNS15767治具

北美UL/CSA标准

美国UL498/817/498A量规

加拿大CSA C22.2No.42量规

欧洲EN|VDE国家标准

德国VDE0620量规

欧规EN50075量规

英国BS1363量规

法国NF C61-314量规

丹麦DS 60884-2-D1

荷兰NEN1020量规

意大利CEI23-50量规

瑞士SEV1011量规

比利时NBN C61-112-1量规

中国GB标准量规

中国GB1002量规

中国GB1003量规

非洲|中东|澳洲国家标准

澳洲AS/NZS3112量规

南非SANS164-1量规

沙特SASO2203|2204量规

东南亚国家标准

印度IS1293量规

泰国TIS 166-2535量规

南美洲国家标准

阿根廷IRAM2063|2073量规

巴西NBR14136量规

医疗器械

ISO594量规

ISO5356 量规

ISO8185 量规

ISO8638 量规

灯具量规

联系方式

深圳市美华安规仪器有限公司

地址: A. 深圳光明新区光明
        圳美311号/518107

         B. 东莞大岭山镇渭

         溪路/523829

热线: 155-0203-6348;  
         136-1283-4185

电话: 0755-3288-5887
传真: 0755-3288-5887

Q Q: 1-4848-7-5858;
        4-9327-8805       

邮箱: sm#ag17.wang

          okgang#163.com
       (#请改@)

官网: www.ag17.wang

论坛: bbs.ag17.wang

当前位置:网站首页 > 量规 > 非洲|中东|澳洲国家标准 > 澳洲AS/NZS3112量规
澳洲AS/NZS3112量规

澳洲AS/NZS 3112条款2.8.1节插销到边沿距离检测规|澳规插头PIN 9mm距离量规|The 9 mm distance gauge for SAA plug pin and the edge of AS/NZS 3112 clause 2.8.1

澳洲AS/NZS 3112条款2.8.1节插销到边沿距离检测规|澳规插头PIN 9mm距离量规|The 9 mm distance gauge for SAA plug pin and the edge of AS/NZS 3112 clause 2.8.1
  • 美华特价
  • 论坛交流
  • 商城购买
  • 邮件订购

详细描述

澳洲AS/NZS 3112条款2.8.1节插销到边沿距离检测规|澳规插头PIN 9mm距离量规|The 9 mm distance gauge for SAA plug pin and the edge of AS/NZS 3112 clause 2.8.1

标准:符合AS/NZS 3112-2012(或最新版)要求;

规格:条款2.8.1节边沿距离检测规需配合图A1或图B1或图F1(a)/ F1(b)量规使用

数量:1个

使用要求:

低压扁平插片插头和具有一个圆形接地片及二个扁平带电插片或二个圆形带电片及一个扁平接地片的低压插头应符合图 2.1所示的呎寸. 任何插头的带电片与插头注塑边缘之间的距离应不小于9mm.当怀疑符合此要求时, 将附录A的图A1或附录B的图B1或附录F的图F1(a), F1(b)的适当治具置于插片上以接触插头面的最高点.使用宽度大于 3mm的 1.5mm厚薄规插入插头和插头治具之间(不用力),在 9mm 之内应不可接触到带电插片.

Low voltage flat-pin plugs and low voltage plugs having one round earth pin and two flat live pins or two round live pins and one flat earth pin, with ratings up to and including 20 A, shall conform to the appropriate dimensions shown in Figure 2.1.

In addition to the dimensions of Figure 2.1, the distance between a live pin of any plug and the edge of the moulding of the plug shall be not less than 9 mm. Where doubt exists regarding compliance with this requirement, the gauge of Figure A1 in Appendix A or Figure B1 in Appendix B, or Figure F1(a) or F1(b) in Appendix F, as appropriate, shall be

placed over the pins to ensure contact with the highest points associated with the plug face.

Using a 1.5 mm feeler gauge of greater than 3 mm width and applied without undue force between the plug and the plug gauge, penetration to within 9 mm of the live pin shall not be possible. 


安规仪器网/美华安规仪器---追崇原创、重视知识产权和尊重劳动成果,也是行业发展主旨,禁止盗链、采集、复制及转载等非法行为,一经发现保留追责权力。


标签:   SAA插头量规  澳规插头量规
点击次数:  更新时间:2016-09-25 21:09:07  【打印此页】  【关闭】
上一条:澳洲AS/NZS 3112条款3.14.5节插座温升测试用插头|SAA插座温升测试治具|Test plug of the temperature rise test for socket-outlets of AS/NZS 3112 clause 2.8  下一条:澳洲AS/NZS 3112 图C1正常插入的试验插头|试验指|正常插入的三扁平插销测试插头和正常插入中试验指测试规|FIGURE C1-THREE-PIN TEST PLUG FOR CHECKING THREE-PIN FLAT PIN 250 V MAX. SOCKET-OUTLETS AGAINST THE STANDARD TEST FINGER IN ACCORDANCE WITH CL
证书查询|安规工具|标准汇总|各国认证|学术文章|新闻|公司动态|测试|安规|标准|智能|下载|搜索|联系我们|在线反馈|在线留言|导航

版权所有:安规仪器网|www.ag17.wang Copyright 2011-2016 All Rights Reserved '); })();

广东深圳  粤ICP备15096309-1号 

电话:0755-3288 5887; 手机:155-0203-6348, 136-1283-4185; QQ:1-4848-7-5858; 49327-8805; 邮箱:sm#g17.wang;  okgang#163.com(点击或#请改@)

安规仪器网|UL498量规|IEC60320量规|灯头量规|灯座量规|IEC61032试验指|UL弯指|H5025喷灯|燃烧测温铜块|漏电起痕电极|灼热丝校温银箔

Powered by MetInfo 5.3.17 ©2008-2017  www.metinfo.cn