IEC60400-2014管形荧光灯灯座和起动器座Lampholders for tubular fluorescent lamps and starterholders

IEC 60400-2014
中文名称： 管形荧光灯灯座和起动器座
英文名称： Lampholders for tubular fluorescent lamps and starterholders
版本： 第7.2版  标准状态： 现行
中国标准分类
(CNS)： 【K74】  国际标准分类
(ICS)： 【29.140】
发布日期： 2014-06-01  正版打印价格： 元
实施日期： 2014-06-01  页数： 360
废止日期：
适用范围： This International Standard states the technical and dimensional requirements for lampholders
for tubular fluorescent lamps and for starterholders, and the methods of test to be used in
determining the safety and the fit of the lamps in the lampholders and the starters in the
starterholders.
This standard covers independent lampholders and lampholders for building-in, used with
tubular fluorescent lamps provided with caps as listed in Annex A, and independent
starterholders and starterholders for building-in, used with starters in accordance with
IEC 60155, intended for use in a.c. circuits where the working voltage does not exceed 1 000 V
r.m.s.
This standard also covers lampholders for single-capped tubular fluorescent lamps integrated
in an outer shell and dome similar to Edison screw lampholders (e.g. for G23 and G24 capped
lamps). Such lampholders are tested in accordance with the following clauses and subclauses
of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9.
This standard also covers lampholders which are integral with a luminaire or intended to be
built into appliances. It covers the requirements for the lampholder only. For all other requirements,
such as protection against electric shock in the area of the terminals, the requirements of the
relevant appliance standard are to be observed and tested after building into the appropriate
equipment, when that equipment is tested according to its own standard. Lampholders for use
by luminaire manufacturers only are not for retail sale.
This standard also applies, as far as is reasonable, to lampholders and starterholders other
than the types explicitly mentioned above and to lamp connectors.
Where the term "holder" is used in the standard, both lampholders and starterholders are
intended.
Where the term “bi-pin lampholder” is used, lampholders for wedged caps are also intended.
   引用了下列标准（标注*的引用文件，其最新版本适用于本标准）
  * IEC 60061-1-2005  灯头、灯座及检验其安全性和互换性的量规 第1部分：灯头
  * IEC 60061-2-2005  灯头、灯座及检验其安全性和互换性的量规 第2部分：灯座
  IEC 60061-3-2001  灯头、灯座以及检验互换性和安全性的量规. 第3部分:量规
  IEC 60068-2-20-1979 
  IEC 60068-2-75-1997  环境试验--第2部分:试验Eh:锤试验
  * IEC 60081-2002  双端荧光灯 性能规范
  IEC 60112-2003  固体绝缘材料试验测定和比较追踪指数
  * IEC 60155-1993  荧光灯用辉光起动器
  * IEC 60238-2011  爱迪生螺口灯座
  IEC 60352-1-1997  无焊连接.:无焊绕接连接.第1部分:绕扎连接.一般要求、试验方法和实用指南
  * IEC 60399-2008  带灯罩卡环的灯座的圆筒螺纹
  IEC 60529-1989  外壳防护等级(国际防护等级代码)
  IEC 60529-1989/AMD.1-1999  外壳防护等级(国际防护等级代码)
  * IEC 60598-1-2014  灯具--第1部分：一般要求和试验
  IEC 60664-1-2007  低压系统内设备的绝缘配合.第1部分:原则、要求和试验
  IEC 60695-11-5-2004  着火危险试验.第11-5部分:针状火焰试验方法.装置、证实试验协议和指南
  IEC 60695-2-11-2000  着火危险试验 第2-11部分:基于灼热/发热丝的试验方法 最终产物的灼热丝易燃性试验
  * IEC 61199-2012  单端荧光灯--安全规范
  ISO 4046-4-2002  纸,纸板,纸浆和类似术语-词汇-第4部分:纸和纸板等级和转换产品
  被下列标准引用
  IEC 60598-1-2014  灯具--第1部分：一般要求和试验